Please, check our SMD/THT services - smd.lotharek.pl; from idea to ready devices                                                                                                                                   

Please, check our SMD/THT services - smd.lotharek.pl; from idea to ready devices                                                                                                                                   

Currency

Shop categories

W Hydra REVISED (processing time 7 days)


W Hydra REVISED

Our price:

1129.00 PLN

Change currency:

USDGBPEUR

Weight: 1.3 kg

Login or register to buy

Buy more, pay less:

  • for 2 pieces and more - 3% (1095.13 PLN)
  • for 5 pieces and more - 6% (1061.26 PLN)
  • for 10 pieces and more - 9% (1027.39 PLN)
  • for 50 pieces and more - 12% (993.52 PLN)
Like Ask Tell

 

 

Fully automatic SCART switch with full galvanic inputs separation.

  (bold - new features comparing  to W-HYDRA)

  • 16 scart inputs ( RGB, s-video, composite) 
  • 1 scart ouput
  • "Knight rider" style active scart detection 
  • full ROHS
  • expandable with 2 additional HYDRA HEADS devices to offer outstanding 24inputs scart functionality
  • AVR controller with firmware future updates
  • HQ plexi transparent ( made by me ;-) at my laser machine)
  • MICRO USB power supply (regular mobile phone charger 5V will do the job - please, use sth decent - approx 1A)
  • Improved signal detection histerisis / all cables shall work now/
  • audio buffer for scart audio output to reduce "hearable audio pops" 
  • SYNC ON GREEN  mode for scart input 2 (SW7 - SOG SWITCH)
  • RGB ONLY / AUTO mode for scart input 8 (SW8 )

 

 

 

Do not use garbage power supply – any decent micro usb mobile charger will do the work.. and please be careful with USB SOCKET 😉

 

 

How doees it work ?

      Imagine, You have many retro system in use. Amiga, Atari ST, ZX spectrum, etc... And You have only one classical TV/Monitor with one SCART INPUT. Each time, You want to switch system, You have to connect Your machine to Your monitor. Everytime, You do it - You damage scart socket inside. Those days are over. Connect up to 8 computers/consoles to HYDRA, then connect HYDRA to Your TV/Monitor and power on hydra with You mobile phone charger with MICRO USB plug. Since now, HYDRA will detect active scart input and forward all signals to Your monitor. Simple and efficent.

 

 

NEVER connect / disconnect SCART PLUGS 

when HYDRA is ON

especially when CONSOLE/SYSTEM is ON !

 

 

You may ask why..

           Designing device, I put much effort  into ability to  passthrough many types of signals: from composite to component. To protect device and not to cut signal`s range, HYDRAs have additional ESD protection diodes, but for a short period of time when scanning for active scart, Hydra is defenseless. If You got hit that moment plugging powered on device, You will damage RGB chip with ESD voltage that may reach thousands of  volts (not dangerous for you, but electronics is fragile..). This chip may become very hot and protection will probably brick hydra till one of chips is replaced (NCS2564). Cost of repair is 10Euro !!!

 

Possible symptoms:

  • knight rider effect stops
  • one scart port doesn`t work
  • Interferences between ports
  • HD led doesn`t work anymore
  • only one port gives correct picture; others are darker....

 

USE SIMPLEST SCART CABLES POSSIBBLE

 

  • No tricky electronics inside as NOT NEEDED. Hydra has built in all necessary features
  • Hydra accepts following sync signals at pin 20 of scart:
    • composite video 
    • luma
    • composite sync  ( please, read FAQ tab above)

 

 

BUTTONS:

  • left - scan for active source to the left from active one (if active is far left, no action) /  next scart in manual mode
  • right - scan for active source to the right from active one (if active is far right, no action) / previous scart in manual mode
  • middle - HD/LOW PASS filter (led on/off) - default ON
  • left+right pressed - disables "knight rider led effect"
  • middle + right - Automatic/manual mode

 

 


Product gallery


 

 

FIRMWARE UPDATE PROCEDURE: (thanks to Frank Skilton for debugging)

  • download last firmware from FILES section
  • connect usbasp (or any avr programmer) to KANDA connector of HYDRA (PINOUT)  ( HIROSE DF13A-6P-1.25H )
  • run Your AVR programming software
  • load *.XEX file; do not change any fuses !
  • flash it

 

 

 

Q.What happens if i have two active sources the same time ?

Nothing, First applied input is a master signal. You can switch to next one by pressing buttons ( previous/next) or switching  first computer off

 

 

Q. I want to send component through the whydra2 as well and I wonder if that is possible?

480p component works well through the W-Hydra2 with proper adapter ( https://www.amazon.de/Scart-Svideo-Comp-Kurzad-umschaltbar/dp/B0014HB7T6) - Thaks Jonas to  for deep tests and report !!

 

480p (reported as 525p 50Hz on ossc) works
480p (reported as 525p 60Hz on ossc) works
720p (reported as 750p 50Hz on ossc) works
720p (reported as 750p 60Hz on ossc) works
1080i (reported as 1125i 50Hz on ossc) works
1080i (reported as 1125i 60Hz on ossc) works
1080p (reported as 1125p 50Hz on ossc) works
1080p (reported as 1125p 60Hz on ossc) works