Please, check our SMD/THT services - smd.lotharek.pl; from idea to ready devices
Please, check our SMD/THT services - smd.lotharek.pl; from idea to ready devices
PID: LOTH000432
VERY IMPORTANT !
Please, be aware preorders have priority, thus new orders will realised by fifo means.
5-7 workdays approximatelly
BISON PROF is a DivMMC-compatible interface for the ZX Spectrum that goes far beyond mass storage. One board plugs into the expansion port and gives your machine an SD card with esxDOS, USB keyboard, mouse and joypad, a classic DB9 joystick port, a full stack of FPGA sound chips, a real-time clock and a DVI-I video output — digital DVI, VGA 31 kHz or RGB 15 kHz.
Everything is built around a Gowin GW1N-9 FPGA and an ATSAMD21 USB controller, with 8 MB of PSRAM, 4 MB of flash and 512 KB of SRAM on board. The real Z80 in your Spectrum stays in charge — BISON PROF simply gives it everything it never had.
FIRST PROTO
A dedicated ATSAMD21 USB host controller handles modern input devices — no drivers, no configuration, just plug in.
All sound chips are implemented in the FPGA and mixed into one stereo output.
| Chip | Details |
|---|---|
| TurboSound FM | 2 × AY-3-8912 + 2 × YM2203 (OPN) — FM and PSG together |
| General Sound | up to 4 MB of sample memory |
| SAA1099 | 6-voice stereo |
BISON PROF takes the picture of your Spectrum and puts it out on a modern monitor. The clock generator is locked to the computer, so the image is stable and pixel-exact.
| Output | Signal |
|---|---|
| DVI digital | 720 × 576 @ 50 Hz, TMDS |
| VGA | 31 kHz (line-doubled) |
| RGB | 15 kHz, for CRT / SCART monitors |
BISON PROF does not take the picture from your Spectrum's video output. Instead, it listens to the Z80 bus and copies every write to screen memory (bank 5, and on 128K machines also bank 7) into its own 16 KB video memory. Border colour and the active screen are taken from ports #FE and #7FFD.
A complete ULA replica in the FPGA then draws the picture from scratch — RGB 15 kHz, VGA 31 kHz through the scandoubler, and digital DVI. The original ULA keeps running the computer, but its video signal is not used at all, so the image is perfectly clean no matter what condition the RF modulator or the composite circuit is in.
Because the picture is generated by BISON PROF, ULAplus comes for free. The FPGA watches the standard ULAplus ports #BF3B (register) and #FF3B (data), keeps the 64-colour palette and applies it to its own video output. Software can detect ULAplus by reading #FF3B.
No ULA replacement, no modification of the computer — ULAplus games and demos simply show their full palette on the BISON PROF output. It can be switched on or off in the setup menu (not available in Pentagon mode).
You do not have to tell BISON PROF what it is plugged into. It measures the period of the Z80 interrupt with a crystal-accurate timer and recognises the machine from the frame length:
| Machine | Frame | Interrupt period |
|---|---|---|
| ZX Spectrum 48K | 69888 T @ 3.5000 MHz | 19.968 ms |
| ZX Spectrum 128K / +2 | 70908 T @ 3.5469 MHz | 19.992 ms |
| Pentagon | 71680 T @ 3.5000 MHz | 20.480 ms |
The 48K and 128K differ by only 0.1 %, yet the detector tells them apart with a safety margin several times larger than crystal tolerance. Detection runs continuously, so it follows multi-clone boards (such as Kraken) that switch machine type on the fly. A separate hardware line tells Sinclair 48K/128K/+2 apart from the +2A/+3, so BISON PROF disables the internal ROM the right way on each model (ROMCS or ROM1OE/ROM2OE).
Most video add-ons run on their own crystal and only approximate the computer's timing — which shows up as drifting, tearing or dropped frames. BISON PROF does it properly.
The result: the picture is locked to your Spectrum frame by frame. No drift, no tearing, no dropped frames — border effects, multicolour engines and raster tricks look exactly as their authors intended.
BISON PROF carries 4 MB of flash memory, and it is yours to fill. At power-on the whole flash is copied into fast PSRAM, so everything stored there is available instantly.
BFC — BIZON Flash Creator - please, refer to FILES tab above
Building the flash contents takes a minute with BFC, a free tool that runs in your web browser — no installation, works offline. Drop in your ROM files and SNA/Z80 snapshots, give the ROMs a name, add a General Sound ROM if you want one, and BFC shows how much space is left. Then choose how you want to program it:
| Method | How it works |
|---|---|
| USB stick | BFC saves a 4 MB image bizonflash.bin. Copy it to a USB stick, hold Left + Middle while switching on — the flash is written with a progress bar on screen. Only sectors that changed are rewritten, so updates are quick |
| TAP file | BFC generates a .TAP that programs the flash from the Spectrum itself. Load it from the SD card with esxDOS, or even from a real tape — no PC connection, no USB stick needed |
You can rebuild and reflash as often as you like — the setup menu is always part of the image, so the machine never ends up without it.
Setup menu (BIOS) - PRESS LEFT BUTTON
Machine settings, ROM selection and joystick modes are set in an on-screen menu — settings are stored in flash and survive firmware updates.
1,2,3 - to select tabs: General,Audio, Video
H- Help
![]() |
![]() |
![]() |
Firmware update from a USB stick
Hold the Left + Middle buttons while switching on. BISON PROF reads the files from the stick and shows the progress on screen:
| File | What it updates |
|---|---|
bizonARM.bin |
USB controller firmware |
bizonFPGA.bin |
FPGA core |
bizonflash.bin |
flash contents made with BFC (ROMs, games, setup) — your settings are kept |
Any combination of the files can be on the stick; when done, the screen says REMOVE PENDRIVE AND POWER OFF.
![]() |
![]() |
![]() |
![]() |
Z80 bus diagnostic
Hold the Left button while switching on and BISON PROF turns into a bus monitor. While your Spectrum runs its own ROM, the FPGA watches every line of the Z80 bus and reports on screen:
A great help when bringing an old machine back to life — you see exactly which line is the problem.

| Part | Specification |
|---|---|
| FPGA | Gowin GW1N-9 |
| USB controller | Microchip ATSAMD21 |
| Memory | 8 MB PSRAM + 4 MB flash (user ROMs and games) + 512 KB SRAM |
| Video | DVI-I (DVI / VGA 31 kHz / RGB 15 kHz), ULAplus, genlock to the host |
| Storage | microSD (DivMMC / esxDOS) |
| Inputs | USB host (keyboard, mouse, joypad), DB9 joystick |
| Other | real-time clock, 3 multifunction buttons (BIOS, reset, esxDOS) |
Firmware is in progress and more features are on the way — follow the FILES tab for updates.
USB keyboard / General Sound demo (2 MB, 16 MHz)
BISON PROF has three buttons on the board — LEFT, MIDDLE and RIGHT. The most important ones are also available on a USB keyboard.
▶ Buttons — normal operation
| Button | Function | USB key |
|---|---|---|
| LEFT | Setup menu (BIOS) — machine settings, ROM selection, joystick modes, video options. Inside the menu press S to save; pressing LEFT again leaves without saving. | F1 |
| RIGHT | NMI / Reset — in DivMMC mode opens the esxDOS NMI menu (file browser, snapshot save/load) and also resets General Sound. When the Spectrum runs one of your own ROMs from flash, RIGHT resets the computer. | F2 |
| MIDDLE | reserved for future firmware | — |
⚡ Buttons — held while switching on
| Hold | Function |
|---|---|
| LEFT + MIDDLE | Firmware update from a USB stick (bizonARM.bin, bizonFPGA.bin, bizonflash.bin) with progress shown on screen. Finished when the screen says REMOVE PENDRIVE AND POWER OFF. |
| LEFT | Z80 bus diagnostic — release the button, let the Spectrum start, then press LEFT to begin the test (press again to restart). Every address, data and control line is shown as active, stuck low/high or shorted, together with CPU clock and interrupt frequency. |
⌨ USB keyboard — special keys
| Key | Function |
|---|---|
| F1 | same as the LEFT button (setup menu) |
| F2 | same as the RIGHT button (NMI menu / reset) |
| F3 | arrows as joystick — on / off |
| F5 | reset the Spectrum |
| F10 | types and runs a short test BASIC program (keyboard check) |
| F12 | types the USB controller firmware version |
✎ USB keyboard — typing
| PC key | Spectrum |
|---|---|
| Shift | CAPS SHIFT |
| Ctrl / Alt | SYMBOL SHIFT |
| Backspace / Delete | DELETE (CAPS + 0) |
| Esc | EDIT (CAPS + 1) |
| Caps Lock | CAPS LOCK (CAPS + 2) |
| Tab | EXTENDED MODE (CAPS + SYMBOL) |
| ← ↑ ↓ → | cursor keys (CAPS + 5 / 7 / 6 / 8) |
| - = # ; ' , . / | typed directly — the matching SYMBOL SHIFT combination is generated |
| Numeric keypad | digits 0–9, ENTER and + − * / |
◉ USB keyboard — arrows as joystick (F3)
| Key | Function |
|---|---|
| ← ↑ ↓ → | joystick directions (in the joystick mode selected for USB in the setup menu) |
| Left Ctrl | FIRE 1 |
| Left Alt | FIRE 2 |
| Right Shift | CAPS SHIFT (typing still possible) |
| Right Ctrl / Alt | SYMBOL SHIFT |
When a USB joypad is connected it takes over, and the arrows go back to working as cursor keys.
Q: I bought a DVI–VGA cable (or adapter) and I get no picture. Why?
A: BIZON PROF picks the video output on its own. When it detects a digital DVI monitor, it turns on the digital signal and switches off the analog VGA output. When no DVI monitor is present, it outputs analog VGA. You don’t need to set anything manually.
A DVI monitor is detected on pin 16 of the connector (Hot Plug Detect). The computer puts +5 V on pin 14, and a connected DVI monitor sends that voltage back on pin 16 to say “I’m connected”.
Many DVI–VGA cables and adapters short pins 14 and 16 together inside. The voltage from pin 14 comes straight back on pin 16, even when a plain VGA monitor is on the other end. BIZON reads this as a connected DVI monitor, switches to the digital output and turns VGA off. The VGA monitor gets no signal and the screen stays black. Neither BIZON nor the monitor is faulty; it’s how the cable is built.
How to fix it: remove pin 16 from the cable’s DVI plug
Without pin 16, the detection signal from the cable never reaches BIZON. BIZON then correctly detects a VGA monitor and sends the picture to it.
Removing pin 16 does not affect VGA picture quality, because that pin carries only the detection signal, not the picture. The change is permanent, so use the modified cable with VGA monitors only. Don’t modify DVI–DVI cables; they work correctly as they are.

Q: Why doesn’t BIZON PROF have HDMI?
There are two reasons.
1. Licensing costs. HDMI is not an open standard. To put an HDMI connector on a product, or even use the HDMI name, the manufacturer has to become a licensed HDMI Adopter. That means an annual fee of up to around US$10,000 plus per-unit royalties. For a small hobby production run, that cost would make the board much more expensive for everyone. DVI carries the same digital picture and can be used freely, without any licence fees.
2. HDMI can’t carry native 15 kHz RGB. A big part of BIZON PROF is authentic analog RGB 15 kHz output, the same kind of signal as the original ZX Spectrum, Amiga or VBXE. It goes straight into a CRT, a SCART TV or a scaler without any conversion. HDMI is a purely digital interface, and its lowest standard modes are already well above that. A connector that can’t output 15 kHz would take away exactly what retro users value most. The video output therefore offers all three options: analog RGB 15 kHz, VGA 31 kHz, and digital DVI.
Can I still connect it to an HDMI TV or monitor?
Yes. The DVI output is electrically compatible with HDMI displays. Use a simple passive DVI-to-HDMI cable or adapter and you get a clean digital picture on any HDMI TV or monitor. Sound is available from the stereo audio jack.
Q: I saw a battery on the pictures, what is it for?
A: BISON PROF has a battery backed up RTC, so your ZX/ESXDOS will get current time and date on every restart instead of the usual year 1987.
LOTHAREK FHU Przemysław Krawczyk
ul. Bukowa 18
42-610 Miasteczko Śląskie, Polska
E-mail: lotharek@lotharek.pl
NIP UE: PL6312246599
Identyfikator produktu (PID): LOTH000432
Nazwa produktu: BISON PROF
Pobierz Deklarację Zgodności UE (PDF)
Produkt przeznaczony jest dla użytkowników posiadających podstawową wiedzę techniczną w zakresie montażu i obsługi urządzeń elektronicznych. Przed instalacją lub podłączeniem urządzenia należy odłączyć zasilanie sprzętu, w którym jest ono montowane.
Produkt spełnia wymagania norm RoHS oraz WEEE. Urządzenia elektroniczne i elektryczne nie powinny być wyrzucane razem z odpadami komunalnymi — po zakończeniu eksploatacji należy przekazać je do punktu zbiórki zużytego sprzętu elektronicznego.
LOTHAREK FHU Przemysław Krawczyk
Bukowa 18
42-610 Miasteczko Śląskie, Poland
E-mail: lotharek@lotharek.pl
EU VAT: PL6312246599
Product identifier (PID): LOTH000432
Product name: BISON PROF
Download EU Declaration of Conformity (PDF)
This product is intended for users with basic technical knowledge of installing and handling electronic devices. Disconnect power from the host device before installing or connecting this product.
This product complies with RoHS and WEEE requirements. Electronic and electrical equipment must not be disposed of with household waste — please take it to an appropriate e-waste collection point at the end of its life.
LOTHAREK FHU Przemysław Krawczyk
Bukowa 18
42-610 Miasteczko Śląskie, Polen
E-Mail: lotharek@lotharek.pl
USt-IdNr.: PL6312246599
Produktkennzeichnung (PID): LOTH000432
Produktname: BISON PROF
EU-Konformitätserklärung herunterladen (PDF)
Dieses Produkt richtet sich an Nutzer mit grundlegenden technischen Kenntnissen beim Einbau und Umgang mit elektronischen Geräten. Trennen Sie das Zielgerät vor dem Einbau oder Anschluss von der Stromversorgung.
Dieses Produkt erfüllt die Anforderungen von RoHS und WEEE. Elektro- und Elektronikgeräte dürfen nicht über den Hausmüll entsorgt werden — bitte geben Sie das Gerät am Ende seiner Lebensdauer bei einer entsprechenden Sammelstelle ab.